Hilti HKD-TE-CX M10 3/8"x30 Setting Tool - Part 2112751, SDS-Plus

--------------------------------------------------

DRILL AND SET WITH ONE TOOL

--------------------------------------------------

HILTI PART NUMBER: 2112751

HKD-TE-CX M10 3/8" x 30

SETTING TOOL WITH INTEGRATED STOP DRILL BIT

CONNECTION END: TE-C (SDS-PLUS)

Hilti's own description of what this changes:

"NO NEED TO CHANGE TOOLS - DRILLING AND

SETTING CAN BE DONE WITH THE SAME TOOL."

"DRILL HOLES PRECISELY TO THE DESIRED DEPTH."

That is the entire argument for it, and anyone who

has installed drop-in anchors overhead will

recognise the problem it solves.

THE CONVENTIONAL SEQUENCE: drill with a bit,

swap to a depth gauge or guess, clean the

hole, swap to a setting punch, drive the

anchor.

WITH THIS: drill to the stop, drop the anchor

in, set it. Same tool, same hand, same

position.

On a suspended ceiling, working above your head

off a platform, that difference is measured in

hours across a job.

--------------------------------------------------

THE STOP IS THE PRECISION

--------------------------------------------------

THE STOP IS BUILT INTO THE BIT.

A drop-in anchor only develops its rated load if

the hole is the correct depth. Too shallow and the

anchor will not seat; too deep and it sits below

the surface with nothing bearing on it.

An integrated stop removes the judgement

entirely - the hole is right every time, by

every operator on the crew, which is why this

tooling exists in a professional range rather

than a consumer one.

HILTI ALSO NOTE: THE 25 mm ANCHOR LENGTH

REDUCES THE RISK OF REBAR HITS WHEN DRILLING.

A shorter hole is less likely to find reinforcement

in the slab. In reinforced concrete that matters -

a rebar strike means a wasted hole, a damaged bit,

and a new position to mark out.

--------------------------------------------------

TUNGSTEN CARBIDE, MULTI-CUTTER

--------------------------------------------------

HEAD MATERIAL: TUNGSTEN CARBIDE

HEAD SHAPE: MULTI CUTTER

BASE MATERIAL: CONCRETE AND REINFORCED

CONCRETE

WORKING MODE: HAMMER DRILLING

PRODUCT CLASS: ULTIMATE

(Hilti's highest tier)

A multi-cutter head - more carbide edges than a

conventional two-flute bit - cuts faster and

survives contact with aggregate and reinforcement

better than a standard tip.

TE-C (SDS-PLUS) SHANK - fits any SDS-plus

rotary hammer, Hilti or otherwise.

--------------------------------------------------

THIS IS THE COMPLETE SET

--------------------------------------------------

Worth stating clearly, because Hilti sell two

things with nearly the same name:

HKD-TE-CX THE FULL SET - setting tool AND

drill bit. THIS LISTING.

HKD-TE-CX-B A SPARE PART - the drill bit

only.

If you need a replacement bit for a setting tool

you already own, that is the -B part, not this

one. Ask me.

--------------------------------------------------

SPECIFICATIONS

--------------------------------------------------

Brand : HILTI

Part number : 2112751

Designation : HKD-TE-CX M10 3/8" x 30

Type : Setting tool with

integrated stop drill

bit

Connection end : TE-C (SDS-plus)

For anchors : Hilti HKD drop-in

anchors, M10 / 3/8"

Base material : Concrete, reinforced

concrete

Working mode : Hammer drilling

Head shape : Multi cutter

Head material : Tungsten carbide

Product class : Ultimate

Supplied : Setting tool AND drill

bit (complete set)

Pack size : 1 piece

Condition : NEW

[CONFIRM AND ADD: DRILL BIT DIAMETER, OVERALL

LENGTH, WEIGHT, AND THE EXACT HKD ANCHOR SIZES

THIS TOOL IS APPROVED FOR. CONFIRM WHETHER "x30"

REFERS TO THE ANCHOR LENGTH OR THE SETTING DEPTH,

AND STATE IT PLAINLY - HILTI'S INTERNATIONAL

CATALOGUE LISTS HKD-TE-CX AGAINST 25 mm ANCHORS

AND HKD-TE-CX-B AGAINST 40 mm, SO A BUYER WILL

ASK.]

RELATED (ask me)

HKD-TE-CX-B replacement drill bit only

HKD anchors M6, M8, M10, M12

--------------------------------------------------

KEY FEATURES

--------------------------------------------------

- Drill and set with one tool - no tool change

- Integrated stop drills to the exact required depth every time

- Tungsten carbide multi-cutter head

- TE-C (SDS-plus) shank - fits any SDS-plus rotary hammer

- Hilti "Ultimate" product class

- Complete set, not the bit-only spare

--------------------------------------------------

APPLICATIONS

--------------------------------------------------

Installation of Hilti HKD drop-in anchors - fastening pipes, air ducts and

suspended ceilings in concrete.

--------------------------------------------------

IMPORTANT NOTES

--------------------------------------------------

CONFIRM THE ANCHOR SIZE YOU ARE SETTING

This tool is sized for one anchor. Hilti make the HKD in M6, M8, M10 and

M12, and the setting tools are not interchangeable.

THIS IS THE M10 / 3/8" TOOL.

TELL ME WHICH HKD ANCHOR YOU ARE INSTALLING

AND I WILL CONFIRM BEFORE YOU ORDER.

THE ANCHORS ARE NOT INCLUDED

This is the tool only. HKD drop-in anchors are a separate purchase. Ask me.

IT NEEDS AN SDS-PLUS ROTARY HAMMER

TE-C is Hilti's name for the SDS-plus shank. It fits SDS-plus hammers of any

make.

IT WILL NOT FIT an SDS-max machine, a plain

chuck, or a non-hammer drill.

HAMMER DRILLING MODE, NOT ROTARY ONLY

It is a hammer drill bit. Used in rotary-only mode it will not cut concrete

and will be ruined trying.

CLEAN THE HOLE

Non-negotiable with any mechanical anchor.

Blow or vacuum the dust out before setting the

anchor.

Dust in the hole is the commonest cause of an anchor that does not reach its

rated load, and it is invisible once the anchor is in.

MIND REBAR

A rebar strike damages a carbide bit

immediately.

If the bit stops advancing and the sound

changes, STOP. Do not force it.

Mark a new position.

Hilti's note that the shorter anchor reduces rebar risk is a real benefit,

not a reduction to zero.

CARBIDE IS HARD AND BRITTLE

Do not drop it.

Do not use it on steel, stone or tile.

Inspect the carbide before each use - a

chipped cutter drills oversize.

ANCHOR APPROVALS

Hilti publish approvals and technical data per anchor, not per tool.

IF YOUR WORK IS SUBJECT TO AN ENGINEERING

APPROVAL OR INSPECTION REGIME, obtain the

current documentation for the HKD anchor from

Hilti in your own country. I supply tooling,

not engineering advice, and I will not

pretend otherwise.

NO INTERNATIONAL WARRANTY

Hilti sell and service directly in most countries. A tool bought outside

their local organisation is generally not covered by that organisation's

warranty or service agreement.

I will handle transit damage or a part that is wrong on arrival myself.

JAPANESE MARKET ITEM

Japanese packaging and any documentation in Japanese. Hilti publish English

technical data for the HKD system internationally.

SHIPPED FROM JAPAN

Dispatched from Tokyo with tracking.

Brand	NA
Type	NA
Model	NA
UPC	NA
MPN	NA
Country of Origin	Japan

Hilti HKD-TE-CX M10 3/8x30 Setting Tool 2112751 SDS-Plus Anchor Japan New

Shipping

Specifications