Acrylic Hot Bending Machine Portable Acrylic Angle Bending Machine 110V

Product Overview

The acrylic hot bending machine is a portable and efficient angle bending device for bending, softening and shaping various plastic materials, such as middle or large size acrylic lamp houses, wall skirting, and edgings for door and window frames. It can be applied to various materials, such as acrylic, Perspex, PVC and all other plastics. It is equipped with a water cycle cooling system, facilitating the hot bending and shaping process, as well as ensuring stable operation for a long time.

Product Parameters

Voltage	110V
Frequency	50/60Hz
Power	800W
Maximum heating width	35.43in (900mm)
Heating thickness	≤0.24in (6mm)
Package type	Cardboard Box
Machine size	43.3118.9 inches (11048cm)
Net weight	14.1LBs (6.4kg)
Please note that the cooling water temperature should not exceed 40˚C.

Precaution

1. The heating process leads to high temperature. Do not touch the heating area with fingers or skin.

2. Be sure to use the machine in a safe environment and keep it away from flammables and explosives.

3. Unplug the power cable/cord if the machine will not be used in a long time.

4. During operation, wear heat-resistant gloves to avoid burns.

5. Ensure the water circulating system works normally, and avoid dry burning which will cause damage to the heating tube.

6. After bending, turn off the power and wait the heating tube to naturally cool down before storage.

Product Features

1. High Efficiency: Adopting the numerical control system and special temperature controller, achieving precise control over the heating temperature and greatly improving the hot bending efficiency and precision.

2. High Precision: Equipped with a length positioner, ensuring the bending precision and enhancing the qualification rate.

3. Good Portability: Using the portable structural design, abandoning the complex operation system, simplifying the operation process and facilitating carrying and application.

4. Durable Accessories: Equipped with a high-power thermostat, a high-temperature-resistant water pump and water pipes, ensuring precise and effective temperature control and efficient water circulation cooling.

5. Wide Application: Suitable for hot bending of various plastic products, such as advertising boards, display cabinets, supermarket shelves, lamp houses and mobile phone supports.

Heating Tube

The machine is equipped with an infrared heating system, adopts a vacuum carbon fiber explosion-proof glass tube, achieves uniform and efficient heating and improves the heating stability and reliability.
　

Power Connector

The independent external power connector is adopted to meet the power safety requirement, and effectively avoids electric leakage and short circuits. The engineering plastic end caps are adopted to improve the operation safety.
　

Water Circulation Cooling System

The water pipe copper connectors are used to be firmly connected with the high-temperature-resistant silicone water pipes, ensuring the water circulation cooling system can work normally and stably.
　

Angle Positioner

The bending angle can be freely adjusted and set through the baffle, well meeting different angle requirements of various materials, greatly improving the bending precision and enhancing the practicability.
　

Operation Method

1. Prepare a cooling tank or bucket with the capacity of 30L or above, fill it with water for cooling. Connect the heater (bending machine) and the pump with the silicone pipe, and then place the pump into the cooling tank or bucket. Turn on the power supply for the pump, and wait for the water to flow smoothly in the pump and pipes.
(Note: After long-term work, the water may get hot, and it needs to be replaced. Do not replace the hot water immediately with very cold water. When the water temperature reaches around 50˚C, just switch off the power/thermostat, wait for a while and then replace the water.)

2. Fit the thermostat with the heater (bending machine), and switch it on. Turn the thermostat clockwise, the temperature will rise; turn it anticlockwise, the temperature drops. Do not turn the thermostat very quickly, or it may not be so accurate to control the temperature.
(Note: Slowly turn the thermostat until you see the heating part becoming fire-red. Extremely high temperature may burn your material to be processed, and the service life of the machine may also be shortened.)

3. After reaching the needed temperature, place the plastic material on the heating area, and make it hot and soft enough for you to bend it with your hands. The time required for heating depends on the materials to be processed, and you can decide on this according to your past experiences.

Tips:
If you are not familiar with hot bending, you can find a small material of the same quality and thickness as the big sheet to be processed. You place the small piece on the heating area and turn the thermostat to find the right heating duration and temperature for the material (with the proper temperature, the material will become soft enough very quickly and blisters will not be caused; if the temperature is too low, the heating efficiency will be affected; if the temperature is too high, blisters may appear). After deciding the right time and temperature, place the large sheet. If you want to have perfect bending to form a desired angle, you can cut a groove along where you expect the angle, and the groove shall be cut to 2/5 thickness of the material; then you begin heating your material, and use anything that can help to form the angle you want.

Recommended temperatures for some regular materials:
Acrylic: 210˚C
Perspex: 195˚C
PVC sheet: 155˚C
ABS: 190˚C
PET: 160˚C

Note: The above temperatures are just for reference, and users may modify them according to their materials and working habits.
　

Product Display

Item Included (022878): 1 x Portable Acrylic Angle Bending Machine 110V

You can make order with no worry.
Any concern just feel free to let us know, we'll reply in 24 hours in normal condition.
Handling Time: Shipping is usually made in 1-3 business days after payments cleared. Orders are processed from Monday-Friday; Not on the weekends & public holidays.
Warranty: 6 months' warranty for the machines, not for the consumables.
We stand behind our products all the item, so even if your warranty period has expired, you can still seek for service or technical support from us with low cost.

On Mar 30, 2026 at 21:53:58 PDT, seller added the following information:

Brand	Techtongda
MPN	022878
Country of Origin	China

New 35 inch Acrylic Bending Machine Acrylic Plastic PVC Bender with Angle

Shipping

Specifications

Returns Accepted